F28M36P63C2ZWTT Texas Instrument IC C2000 REAL TIME MICROCONTROLLERS

The Concerto family is a multicore system-on-chip microcontroller unit (MCU) with independent communication and real-time control subsystems. The F28M36x family of devices is the second series in the Concerto family.

The communications subsystem is based on the industry-standard 32-bit Arm Cortex-M3 CPU and features a wide variety of communication peripherals, including Ethernet 1588, USB OTG with PHY, Controller Area Network (CAN), UART, SSI, I2C, and an external interface.

The real-time control subsystem is based on TI’s industry-leading proprietary 32-bit C28x floating-point CPU and features the most flexible and high-precision control peripherals, including ePWMs with fault protection, and encoders and captures—all as implemented by TI’s

TMS320C2000™ Entry performance MCUs and Premium performance MCUs. In addition, the C28-CPU has been enhanced with the addition of the VCU instruction accelerator that implements efficient Viterbi, Complex Arithmetic, 16-bit FFTs, and CRC algorithms.

A high-speed analog subsystem and supplementary RAM memory is shared, along with on-chip voltage regulation and redundant clocking circuitry. Safety considerations also include Error Correction Code (ECC), parity, and code secure memory, as well as documentation to assist with system-level industrial safety certification.

Features for the F28M36P63C2:

Master Subsystem — Arm® Cortex®-M3
125 MHz
Embedded memory
Up to 1MB of flash (ECC)
Up to 128KB of RAM (ECC or parity)
Up to 64KB of shared RAM
2KB of IPC Message RAM
Five Universal Asynchronous Receiver/Transmitters (UARTs)
Four Synchronous Serial Interfaces (SSIs)
and a Serial Peripheral Interface (SPI)
Two Inter-integrated Circuits (I2Cs)
Universal Serial Bus On-the-Go (USB-OTG) + PHY
10/100 ENET 1588 MII
Two Controller Area Network, D_CAN, modules (pin-bootable)
32-channel Micro Direct Memory Access (µDMA)
Dual security zones (128-bit password per zone)
External Peripheral Interface (EPI)
Micro Cyclic Redundancy Check (µCRC) module
Four general-purpose timers
Two watchdog timer modules
Three external interrupts
Endianness: little endian
Clocking
On-chip crystal oscillator and external clock input
Dynamic Phase-Locked Loop (PLL) ratio changes supported
1.2-V digital, 1.8-V analog, 3.3-V I/O design
Interprocessor Communications (IPC)
32 handshaking channels
Four channels generate IPC interrupts
Can be used to coordinate transfer of data through IPC Message RAMs
Up to 142 individually programmable, multiplexed General-Purpose Input/Output (GPIO) pins
Glitch-free I/Os
Control Subsystem — TMS320C28x 32-bit CPU
150 MHz
C28x core hardware built-in self-test
Embedded memory
Up to 512KB of flash (ECC)
Up to 36KB of RAM (ECC or parity)
Up to 64KB of shared RAM
2KB of IPC Message RAM
IEEE-754 single-precision Floating-Point Unit (FPU)
Viterbi, Complex Math, CRC Unit (VCU)
Serial Communications Interface (SCI)
SPI
I2C
6-channel Direct Memory Access (DMA)
12 Enhanced Pulse Width Modulator (ePWM) modules
24 outputs (16 high-resolution)
Six 32-bit Enhanced Capture (eCAP) modules
Three 32-bit Enhanced Quadrature Encoder Pulse (eQEP) modules
Multichannel Buffered Serial Port (McBSP)
EPI
One security zone (128-bit password)
Three 32-bit timers
Endianness: little endian
Analog Subsystem
Dual 12-bit Analog-to-Digital Converters (ADCs)
Up to 2.88 MSPS
Up to 24 channels
Four Sample-and-Hold (S/H) circuits
Up to six comparators with 10-bit Digital-to-Analog Converter (DAC)
Package
289-ball ZWT New Fine Pitch Ball Grid Array (nFBGA)
Temperature options:
T: –40ºC to 105ºC Junction
S: –40ºC to 125ºC Junction